Home page logo
/

nmap-dev logo Nmap Development mailing list archives

Nmap 6.0 problem
From: Richard Roberts <pixelbrilliance () gmail com>
Date: Tue, 29 May 2012 14:59:50 -0600

Just installed nmap 6.0 on windows 7 64bit.  Whenever I try to scan any
host it fails to determine the route.  I've listed some of the basic
information below, any help would be greatly appreciated.

The only way I've been able to get it to scan is by using the
--unprivileged option.

-=[OUTPUT FROM "nmap -T4 -F 10.150.16.1"]=-
=============================================================
Starting Nmap 6.00 ( http://nmap.org ) at 2012-05-23 15:06 Mountain
Daylight Time

nexthost: failed to determine route to 10.150.16.1

QUITTING!


-=[OUTPUT FROM "nmap --route-dst 10.150.16.1"]=-
=============================================================
10.150.16.1
eth0 eth0 srcaddr 10.150.16.73 direct


-=[OUTPUT FROM "route print"]=-
=============================================================
Active Routes:
Network Destination        Netmask          Gateway       Interface  Metric
          0.0.0.0          0.0.0.0      10.150.16.1     10.150.16.73     10


-=[OUTPUT FROM "nmap --iflist"]=-
=============================================================
Starting Nmap 6.00 ( http://nmap.org ) at 2012-05-23 15:11 Mountain
Daylight Time
************************INTERFACES************************
DEV  (SHORT) IP/MASK                      TYPE        UP   MTU  MAC
eth0 (eth0)  fe80::9489:be0e:9c3e:4536/64 ethernet    up   1500
00:24:7E:01:4F:30
eth0 (eth0)  10.150.16.73/32              ethernet    up   1500
00:24:7E:01:4F:30
eth1 (eth1)  fe80::61a8:6e66:9339:bd6a/64 ethernet    up   1500
00:50:56:C0:00:01
eth1 (eth1)  169.254.189.106/16           ethernet    up   1500
00:50:56:C0:00:01
eth2 (eth2)  fe80::6c5f:7524:8e75:c437/64 ethernet    up   1500
00:50:56:C0:00:08
eth2 (eth2)  192.168.248.1/24             ethernet    up   1500
00:50:56:C0:00:08
lo0  (lo0)   ::1/128                      loopback    up   -1
lo0  (lo0)   127.0.0.1/8                  loopback    up   -1
tun0 (tun0)  fe80::5efe:a96:1049/128      point2point down 1280
tun1 (tun1)  fe80::5efe:a9fe:bd6a/128     point2point down 1280
tun2 (tun2)  fe80::5efe:c0a8:f801/128     point2point down 1280

DEV  WINDEVICE
eth0 \Device\NPF_{FA6B9870-1421-467C-B9E5-1313228A1323}
eth0 \Device\NPF_{FA6B9870-1421-467C-B9E5-1313228A1323}
eth1 \Device\NPF_{141B7E7F-63AA-4B3B-8239-CB1B72616DED}
eth1 \Device\NPF_{141B7E7F-63AA-4B3B-8239-CB1B72616DED}
eth2 \Device\NPF_{C0B8C41A-A151-4762-900D-0AEF52138358}
eth2 \Device\NPF_{C0B8C41A-A151-4762-900D-0AEF52138358}
lo0  <none>
lo0  <none>
tun0 <none>
tun1 <none>
tun2 <none>

ROUTES: NONE FOUND(!)
=============================================================
_______________________________________________
Sent through the nmap-dev mailing list
http://cgi.insecure.org/mailman/listinfo/nmap-dev
Archived at http://seclists.org/nmap-dev/


  By Date           By Thread  

Current thread:
  • Nmap 6.0 problem Richard Roberts (May 29)
[ Nmap | Sec Tools | Mailing Lists | Site News | About/Contact | Advertising | Privacy ]